кто-нибудь ставил FreeBSD на IBM Bladecenter H21?
я поставил версию 7, но есть проблема с сетевой картой.
sometest# ifconfig -a
bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4>
ether 00:1a:64:d1:70:d0
inet 192.168.10.14 netmask 0xffffff00 broadcast 192.168.10.255
media: Ethernet autoselect (1000baseSX <full-duplex>)
status: active
bce1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4>
ether 00:1a:64:d1:70:d2
inet 192.168.15.2 netmask 0xffffff00 broadcast 192.168.15.255
media: Ethernet autoselect (none)
status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
аналогичные сетевые карты вроде бы, но на второй нет линка. на соседних лезвиях, где стоят винды вторая сетевая пашет нормально.
вывод dmesg
bce0: <Broadcom NetXtreme II BCM5708 1000Base-SX (B2)> mem 0xda000000-0xdbffffff irq 17 at device 0.0 on pci4
miibus0: <MII bus> on bce0
brgphy0: <BCM5708S 1000/2500BaseSX PHY> PHY 2 on miibus0
brgphy0: 1000baseSX-FDX, auto
bce0: Ethernet address: 00:1a:64:d1:70:d0
bce0: [ITHREAD]
bce0: ASIC (0x57081021); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); F/W (0x03040405); Flags( MFW MSI )
pcib11: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pci5: <ACPI PCI bus> on pcib11
pcib12: <PCI-PCI bridge> at device 0.0 on pci5
pci6: <PCI bus> on pcib12
bce1: <Broadcom NetXtreme II BCM5708 1000Base-SX (B2)> mem 0xd8000000-0xd9ffffff irq 19 at device 0.0 on pci6
miibus1: <MII bus> on bce1
brgphy1: <BCM5708S 1000/2500BaseSX PHY> PHY 2 on miibus1
brgphy1: 1000baseSX-FDX, auto
bce1: Ethernet address: 00:1a:64:d1:70:d2
bce1: [ITHREAD]
bce1: ASIC (0x57081021); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); F/W (0x03040405); Flags( MSI )
pci0: <base peripheral> at device 8.0 (no driver attached)
pcib13: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib13
вывод pciconf -lv
bce0@pci0:4:0:0: class=0x020000 card=0x03271014 chip=0x16ac14e4 rev=0x12 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme II BCM5708S Gigabit Ethernet'
class = network
subclass = ethernet
pcib12@pci0:5:0:0: class=0x060400 card=0x00000000 chip=0x01031166 rev=0xc3 hdr=0x01
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'BCM5715 Broadcom dual gigabit, pci bridge'
class = bridge
subclass = PCI-PCI
bce1@pci0:6:0:0: class=0x020000 card=0x03271014 chip=0x16ac14e4 rev=0x12 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme II BCM5708S Gigabit Ethernet'
class = network
subclass = ethernet
vi /usr/src/sys/dev/bge/if_bge.c
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5700 },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5701 },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5702 },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5702_ALT },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5702X },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5703 },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5703_ALT },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5703X },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5704C },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5704S },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5704S_ALT },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5705 },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5705F },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5705K },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5705M },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5705M_ALT },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5714C },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5714S },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5715 },
скачал с marvell.com дрова для фрибсд installbsd70x86-10.60.1.3.tar.gz, но эффекта никакого :(
может подскажете в какую сторону копать или сайты где могут помочь с этой проблемой??
