The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Поиск:  Каталог документации

Next Previous Contents

6. Transparent Proxy to a Remote Box

Now, the question naturally arises, if we can do all this nifty stuff redirecting HTTP connections to local ports, could we do the same thing but to a remote box (e.g., the machine with squid running is not the same machine as iptables is running on). The answer is yes, but it takes a little different magic words. If you only want to redirect to the local box (the normal case), skip this section.

For the purposes of example commands, let's assume we have two boxes called squid-box and iptables-box, and that they are on the network local-network. In the commands below, replace these strings with the actual IP addresses or name of your machines and network.

I will present two different approaches here.

6.1 First method (simpler, but does not work for some esoteric cases)

First, we need to machine that squid will be running on, squid-box. You do not need iptables or any special kernel options on this machine, just squid. You *will*, however, need the 'http_accel' options as described above. (Previous version of this HOWTO suggested that you did not need those options. That was a mistake. Sorry to have confused people...)

Now, the machine that iptables will be running on, iptables-box You will need to configure the kernel as described in section 3 above, except that you don't need the REDIRECT target support). Now, for the iptables commands. You need three:

The first one sends the packets to squid-box from iptables-box. The second makes sure that the reply gets sent back through iptables-box, instead of directly to the client (this is very important!). The last one makes sure the iptables-box will forward the appropriate packets to squid-box. It may not be needed. YMMV. Note that we specified '-i eth0' and then '-o eth0', which stands for input interface eth0 and output interface eth0. If your packets are entering and leaving on different interfaces, you will need to adjust the commands accordingly.

Add these commands to your appropriate startup scripts under /etc/rc.d/

(Thanks to Giles Coochey for help writing this section).

6.2 Second method (more complicated, but more general)

Our first shot at this works good, but there is a minor drawback in that HTTP/1.0 connections without the Host header do not get handled properly. Connections that are fully or partially HTTP/1.1 compliant work fine. As most modern web browsers send the Host header, this is not a problem for most people. However, some small programs or embedded devices may send only very simple HTTP/1.0 requests. If you want to support these, we'll need to do a little more work. Namely, on iptables-box we'll need the following options enabled in the kernel in addition to what was specified above:

You'll also need the iproute2 tools. Your distribution probably already has them installed, but if not, look at ftp://ftp.inr.ac.ru/ip-routing/

You'll want to use the following set of commands on iptables-box:

Note that the choice of firewall mark (3) and routing table (2) was fairly arbitrary. If you are already using policy routing or firewall marking for some other purpose, make sure you choose unique numbers here. Otherwise, don't worry about it.

Next, squid-box. Use this command, which should look remarkably similar to a command we've seen previously.

As before, add all of these commands to the appropriate startup scripts.

Here is a brief explanation of how this works: in method one, we used Network Address Translation to get the packets to the other box. The result of this is that the packet gets altered. This alteration is what causes some kinds of clients mentioned above to fail. In method two, we use a magic thing called policy routing. The first thing we do is to select the packets we want. Thus, all packets on port 80, except those coming from squid-box itself, are MARKed. Then, when the kernel goes to make a routing decision, the MARKed packets aren't routing using the normal routing table that you access with the ``route'' command but with a special table. This special table has only one entry, a default gateway to squid-box. Thus, the packet is sent merrily on it's way without every having been altered. So, even HTTP/1.0 connections can be handled perfectly. (Thanks to Michal Svoboda for suggesting and helping to write this section)

6.3 Method One: What if iptables-box is on a dynamic IP?

If the iptables-box is on a dynamic IP address (e.g. a dialup PPP connection, or a DHCP assigned IP address from a cable modem, etc.), then you will want to make a slight change to the above commands. Replace the second command with this one:

This change avoids having to specify the IP address of iptables-box in the command. Since it will change often, you'd have to change your commands to reflect it. This will save you a lot of hassle.


Next Previous Contents


Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру