The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

avmcapictrl (8)
  • >> avmcapictrl (8) ( Linux man: Команды системного администрирования )
  •  

    NAME

    avmcapictrl - Add, reset or remove active AVM cards and load firmware
     
    

    SYNOPSIS

    avmcapictrl add <portbase> <irq> <type>
    avmcapictrl load <bootcode> [<contrnr> [<protocol>

        [P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]]
    avmcapictrl reset [contrnr]
    avmcapictrl remove [contrnr]
    avmcapictrl trace [contrnr] [off|short|on|full|shortnodata|nodata]
    avmcapictrl addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]  

    DESCRIPTION

    avmcapictrl is used to register active AVM ISA cards kernelcapi system and therewith to the isdn system. You need it also to upload the firmware to any active AVM card. If an error occure please also check the kernel error messages by using the command dmesg(8).

     

    COMMANDS

    add <portbase> <irq> <type>
    is used to add a ISA card to the kernel-capi2.0 system. The portbase can have the values 0x150, 0x250, 0x300 and 0x340 for the B1 ISA cards, look at the jumper on the card. For a T1-ISA (HEMA) card you can select an wide range of ports.
    irq can be selected from the following values:
    3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
    type can be B1 or T1.

    load <bootcode> [<contrnr> [<protocol>
    [P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]] is used to load the firmware to a card bootcode is a t4-file. The actual versions of the t4-files for the different d-channel protocols can be found at ftp://ftp.avm.de/cardware/b1/linux/firmware.
    You need different t4-files for different d channel protocols: b1-1tr6.t4 for 1TR6, b1.t4 for DSS1 and
    b1-usa.t4 for 5ESS and NI1 (DSS1 is also supported).
    For M1/M2 PCMCIA cards you need m1-s10.t4 or m1-s4.t4 depending on the handy type used.
    contrnr is the number of the controller (card) starting from 1.
    protocol can be DSS1, CT1, VN3, AUSTEL, 5ESS or NI1.
    P2P point to point
    DN1:SPID1 DN2:SPID2 is for the american protocols 5ESS and NI1.

    reset [contrnr]
    is used to reset a card if loading has failed. This function only make sence if card is not successfully loaded.
    contrnr is the number of the controller (card) starting from 1.

    remove [contrnr]
    is used to remove a card previous added. You can also remove automatic added cards (for example a B1-PCI card).
    contrnr is the number of the controller (card) starting from 1.

    trace [contrnr] [off|short|on|full|shortnodata|nodata]
    is used to trace CAPI2.0 messages. The trace will be done as kernel messages, see dmesg(8).
    contrnr is the number of the controller (card) starting from 1.
    off switch traceing off
    short switch one line per CAPI2.0 message tracing on
    on | full switch on full decode tracing
    shortnodata switch on line per CAPI2.0 message tracing on, but exclude DATA_B3_IND and DATA_B3_REQ messages.
    on | full switch on full decode tracing, but exclude DATA_B3_IND and DATA_B3_REQ messages.

    addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]
    is used to add a card, this is more generic than add.
    driver currently b1isa or t1isa
    portbase can have the values 0x150, 0x250, 0x300 and 0x340 for the b1isa driver, look at the jumper on the card. For t1isa driver you can select an wide range of ports.
    irq can be selected from the following values: 3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
    membase memory address if needed by driver
    cardnr only usefull with driver t1isa

     

    AUTHOR

    Carsten Paeth <calle@calle.in-berlin.de>

     

    SEE ALSO

    ttyI(4), isdnctrl(8), isdninfo(4). dmesg(8). syslogd(8).


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    COMMANDS
    AUTHOR
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру