The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

boot_i386 (8)
  • >> boot_i386 (8) ( FreeBSD man: Команды системного администрирования )

  • BSD mandoc
     

    NAME

    
    
    boot
    
     - system bootstrapping procedures
    
     
    

    DESCRIPTION

    Power fail and crash recovery Normally, the system will reboot itself at power-up or after crashes. An automatic consistency check of the file systems will be performed, and unless this fails, the system will resume multi-user operations.

    Cold starts Most i386 PCs attempt to boot first from floppy disk drive 0 (sometimes known as drive A:) and, failing that, from hard disk drive 0 (sometimes known as drive C:, or as drive 0x80 to the BIOS). Some BIOSes allow you to change this default sequence, and may also include a CD-ROM drive as a boot device.

    By default, a three-stage bootstrap is employed, and control is automatically passed from the boot blocks (bootstrap stages one and two) to a separate third-stage bootstrap program, loader(8). This third stage provides more sophisticated control over the booting process than it is possible to achieve in the boot blocks, which are constrained by occupying limited fixed space on a given disk or slice.

    However, it is possible to dispense with the third stage altogether, either by specifying a kernel name in the boot block parameter file, /boot.config or, unless option -n is set, by hitting a key during a brief pause (while one of the characters - \ | or / is displayed) before loader(8) is invoked. Booting will also be attempted at stage two, if the third stage cannot be loaded.

    The remainder of this subsection deals only with the boot blocks. The loader(8) program is documented separately.

    After the boot blocks have been loaded, you should see a prompt similar to the following:

    >> FreeBSD/i386 BOOT
    Default: 0:ad(0,a)/boot/loader
    boot:
    

    The automatic boot will attempt to load /boot/loader from partition `a' of either the floppy or the hard disk. This boot may be aborted by typing any character on the keyboard at the `boot:' prompt. At this time, the following input will be accepted:

    ?
    Give a short listing of the files in the root directory of the default boot device, as a hint about available boot files. (A ? may also be specified as the last segment of a path, in which case the listing will be of the relevant subdirectory.)

    bios_drive : interface ( unit , [slice , part ] filename [-aCcDdghmnPprsv ] [-S speed ]
    Specify boot file and flags.

    bios_drive
    The drive number as recognized by the BIOS. 0 for the first drive, 1 for the second drive, etc.
    interface
    The type of controller to boot from. Note that the controller is required to have BIOS support since the BIOS services are used to load the boot file image.

    The supported interfaces are:

    ad
    ST506, IDE, ESDI, RLL disks on a WD100[2367] or lookalike controller
    fd
    5 1/4" or 3 1/2" High density floppies
    da
    SCSI disk on any supported SCSI controller

    unit
    The unit number of the drive on the interface being used. 0 for the first drive, 1 for the second drive, etc.
    [slice , part ]
    The partition letter inside the BSD portion of the disk. See bsdlabel(8). By convention, only partition `a' contains a bootable image. If sliced disks are used (``fdisk partitions'' ) any slice (1 for the first slice, 2 for the second slice, etc.) can be booted from, with the default (if not specified) being the active slice or, otherwise, the first Fx slice. If slice is specified as 0, the first Fx slice (also known as ``compatibility'' slice) is booted from.
    filename
    The pathname of the file to boot (relative to the root directory on the specified partition). Defaults to /boot/kernel/kernel Symbolic links are not supported (hard links are).
    [-aCcDdghmnPpqrsv ] [-S speed ]
    Boot flags:

    -a
    during kernel initialization, ask for the device to mount as the root file system.
    -C
    try to mount root file system from a CD-ROM.
    -c
    this flag is currently a no-op.
    -D
    boot with the dual console configuration. In the single configuration, the console will be either the internal display or the serial port, depending on the state of the -h option below. In the dual console configuration, both the internal display and the serial port will become the console at the same time, regardless of the state of the -h option.
    -d
    enter the DDB kernel debugger (see ddb(4)) as early as possible in kernel initialization.
    -g
    use the GDB remote debugging protocol.
    -h
    force the serial console. For instance, if you boot from the internal console, you can use the -h option to force the kernel to use the serial port as its console device. The serial port driver sio(4) has a flag (0x20) to override this option. If that flag is set, the serial port will always be used as the console, regardless of the -h option described here. See the man page for sio(4) for more details.
    -m
    mute the console to suppress all console input and output during the boot.
    -n
    ignore key press to interrupt boot before loader(8) is invoked.
    -P
    probe the keyboard. If no keyboard is found, the -D and -h options are automatically set.
    -p
    pause after each attached device during the device probing phase.
    -q
    be quiet, do not write anything to the console unless automatic boot fails or is disabled. This option only affects second-stage bootstrap, to prevent next stages from writing to the console use in combination with the -m option.
    -r
    use the statically configured default for the device containing the root file system (see config(8)). Normally, the root file system is on the device that the kernel was loaded from.
    -s
    boot into single-user mode; if the console is marked as ``insecure'' (see ttys(5)), the root password must be entered.
    -S speed
    set the speed of the serial console to speed The default is 9600 unless it has been overridden by setting BOOT_COMCONSOLE_SPEED in make.conf5 and recompiling and reinstalling the boot blocks.
    -v
    be verbose during device probing (and later).

    Use the /boot.config file to set the default configuration options for the boot block code. See boot.config5 for more information about the /boot.config file.  

    FILES

    /boot.config
    parameters for the boot blocks (optional)
    /boot/boot1
    first stage bootstrap file
    /boot/boot2
    second stage bootstrap file
    /boot/loader
    third stage bootstrap
    /boot/kernel/kernel
    default kernel
    /boot/kernel.old/kernel
    typical non-default kernel (optional)

     

    DIAGNOSTICS

    When disk-related errors occur, these are reported by the second-stage bootstrap using the same error codes returned by the BIOS, for example ``Disk error 0x1 (lba=0x12345678)'' Here is a partial list of these error codes:

    0x1
    Invalid argument
    0x2
    Address mark not found
    0x4
    Sector not found
    0x8
    DMA overrun
    0x9
    DMA attempt across 64K boundary
    0xc
    Invalid media
    0x10
    Uncorrectable CRC/ECC error
    0x20
    Controller failure
    0x40
    Seek failed
    0x80
    Timeout

    NOTE On older machines, or otherwise where EDD support (disk packet interface support) is not available, all boot-related files and structures (including the kernel) that need to be accessed during the boot phase must reside on the disk at or below cylinder 1023 (as the BIOS understands the geometry). When a ``Disk error 0x1'' is reported by the second-stage bootstrap, it generally means that this requirement has not been adhered to.  

    SEE ALSO

    ddb(4), boot.config5, make.conf5, ttys(5), boot0cfg(8), bsdlabel(8), btxld(8), config(8), halt(8), loader(8), nextboot(8), reboot(8), shutdown(8)  

    BUGS

    The bsdlabel(5) format used by this version of BSD is quite different from that of other architectures.

    Due to space constraints, the keyboard probe initiated by the -P option is simply a test that the BIOS has detected an ``extended'' keyboard. If an ``XT/AT'' keyboard (with no F11 and F12 keys, etc.) is attached, the probe will fail.


     

    Index

    NAME
    DESCRIPTION
    FILES
    DIAGNOSTICS
    SEE ALSO
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру