The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

bpp (7)
  • >> bpp (7) ( Solaris man: Макропакеты и соглашения )
  •  

    NAME

    bpp - bi-directional parallel port
    driver
     
    

    SYNOPSIS

    SUNW,bpp@slot,offset:bppn
    

     

    DESCRIPTION

    The bpp driver provides a general-purpose bi-directional interface to parallel devices. It supports a variety of output (printer) and input (scanner) devices, using programmable timing relationships between the various handshake signals.  

    APPLICATION PROGRAMMING INTERFACE

    The bpp driver is an exclusive-use device. If the device has already been opened, subsequent opens fail with EBUSY.  

    Default Operation

    Each time the bpp device is opened, the default configuration is BPP_ACK_BUSY_HS for read handshake, BPP_ACK_HS for write handshake, 1 microsecond for all setup times and strobe widths, and 60 seconds for both timeouts. This configuration (in the write mode) drives many common personal computer parallel printers with Centronics-type interfaces. The application should use the BPPIOC_SETPARMS ioctl request to configure the bpp for the particular device which is attached, if necessary.  

    Write Operation

    If a failure or error condition occurs during a write(2), the number of bytes successfully written is returned (short write). Note that errno will not be set. The contents of certain status bits will be captured at the time of the error, and can be retrieved by the application program, using the BPPIOC_GETERR ioctl request. Subsequent write(2) calls may fail with the system error ENXIO if the error condition is not rectified. The captured status information will be overwritten each time an attempted transfer or a BPPIOC_TESTIO ioctl request occurs.  

    Read Operations

    If a failure or error condition occurs during a read(2), the number of bytes successfully read is returned (short read). Note that errno will not be set. The contents of certain status bits will be captured at the time of the error, and can be retrieved by the application, using the BPPIOC_GETERR ioctl request. Subsequent read(2) calls may fail with ENXIO if the error condition is not rectified. The captured register information will be overwritten each time an attempted transfer or a BPPIOC_TESTIO ioctl request.

    If the read_handshake element of the bpp_transfer_parms structure (see below) is set to BPP_CLEAR_MEM or BPP_SET_MEM, zeroes or ones, respectively, are written into the user buffer.  

    Read/Write Operation

    When the driver is opened for reading and writing, it is assumed that scanning will take place, as scanners are the only devices supported by this mode. Most scanners require that the SLCT_IN or AFX pin be set to tell the scanner the direction of the transfer. The AFX line is set when the read_handshake element of the bpp_transfer_parms structure is set to BPP_HSCAN_HS, otherwise the SLCT_IN pin is set. Normally, scanning starts by writing a command to the scanner, at which time the pin is set. When the scan data is read back, the pin is reset.  

    IOCTLS

    The following ioctl requests are supported:

    BPPIOC_SETPARMS

    Set transfer parameters.

    The argument is a pointer to a bpp_transfer_parms structure. See below for a description of the elements of this structure. If a parameter is out of range, EINVAL is returned.

    BPPIOC_GETPARMS

    Get current transfer parameters.

    The argument is a pointer to a bpp_transfer_parms structure. See below for a description of the elements of this structure. If no parameters have been configured since the device was opened, the contents of the structure will be the default conditions of the parameters (see Default Operation above).

    BPPIOC_SETOUTPINS

    Set output pin values.

    The argument is a pointer to a bpp_pins structure. See below for a description of the elements of this structure. If a parameter is out of range, EINVAL is returned.

    BPPIOC_GETOUTPINS

    Read output pin values. The argument is a pointer to a bpp_pins structure. See below for a description of the elements of this structure.

    BPPIOC_GETERR

    Get last error status.

    The argument is a pointer to a bpp_error_status structure. See below for a description of the elements of this structure. This structure indicates the status of all the appropriate status bits at the time of the most recent error condition during a read(2) or write(2) call, or the status of the bits at the most recent BPPIOC_TESTIO ioctl request. Note: The bits in the pin_status element indicate whether the associated pin is active, not the actual polarity. The application can check transfer readiness without attempting another transfer using the BPPIOC_TESTIO ioctl. Note: The timeout_occurred and bus_error fields will never be set by the BPPIOC_TESTIO ioctl, only by an actual failed transfer.

    BPPIOC_TESTIO

    Test transfer readiness.

    This command checks to see if a read or write transfer would succeed based on pin status, opened mode, and handshake selected. If a handshake would succeed, 0 is returned. If a transfer would fail, -1 is returned, and errno is set to EIO, and the error status information is captured. The captured status can be retrieved using the BPPIOC_GETERR ioctl call. Note that the timeout_occurred and bus_error fields will never be set by this ioctl.

     

    Transfer Parameters Structure

    This structure is defined in <sys/bpp_io.h>.

    struct bpp_transfer_parms {
       enum  handshake_t
            read_handshake;      /* parallel port read handshake mode */
       int  read_setup_time;    /* DSS register - in nanoseconds */
       int  read_strobe_width;  /* DSW register - in nanoseconds */
       int  read_timeout;       /*
                                 * wait this many seconds
                                 * before aborting a transfer
                                */
       enum handshake_t
            write_handshake;      /* parallel port write handshake mode */
       int  write_setup_time;    /* DSS register - in nanoseconds */
       int  write_strobe_width;  /* DSW register - in nanoseconds */
       int  write_timeout;       /*
                                  * wait this many seconds
                                  * before aborting a transfer
                                 */
    };
    /* Values for read_handshake and write_handshake fields */
       enum handshake_t {
           BPP_NO_HS,            /* no handshake pins */
           BPP_ACK_HS,           /* handshake controlled by ACK line */
           BPP_BUSY_HS,          /* handshake controlled by BSY line */
           BPP_ACK_BUSY_HS,      /*
                                  * handshake controlled by ACK and BSY lines
                                  * read_handshake only!
                                 */
           BPP_XSCAN_HS,         /* xerox scanner mode,
                                  * read_handshake only!
                                         */
           BPP_HSCAN_HS,         /*
                                  * HP scanjet scanner mode
                                  * read_handshake only!
                                 */
           BPP_CLEAR_MEM,        /* write 0's to memory,
                                  * read_handshake only!
                                 */
           BPP_SET_MEM,          /* write 1's to memory,
                                  * read_handshake only!
                                 */
            /* The following handshakes are RESERVED. Do not use. */
           BPP_VPRINT_HS,        /* valid only in read/write mode */
           BPP_VPLOT_HS          /* valid only in read/write mode */
    };
    

    The read_setup_time field controls the time between dstrb falling edge to bsy rising edge if the read_handshake field is set to BPP_NO_HS or BPP_ACK_HS. It controls the time between dstrb falling edge to ack rising edge if the read_handshake field is set to BPP_ACK_HS or BPP_ACK_BUSY_HS. It controls the time between ack falling edge to dstrb rising edge if the read_handshake field is set to BPP_XSCAN_HS.

    The read_strobe_width field controls the time between ack rising edge and ack falling edge if the read_handshake field is set to BPP_NO_HS or BPP_ACK_BUSY_HS. It controls the time between dstrb rising edge to dstrb falling edge if the read_handshake field is set to BPP_XSCAN_HS.

    The values allowed for the write_handshake field are duplicates of the definitions for the read_handshake field. Note that some of these handshake definitions are only valid in one mode or the other.

    The write_setup_time field controls the time between data valid to dstrb rising edge for all values of the write_handshake field.

    The write_strobe_width field controls the time between dstrb rising edge and dstrb falling edge if the write_handshake field is not set to BPP_VPRINT_HS or BPP_VPLOT_HS. It controls the minimum time between dstrb rising edge to dstrb falling edge if the write_handshake field is set to BPP_VPRINT_HS or BPP_VPLOT_HS.  

    Transfer Pins Structure

    This structure is defined in <sys/bpp_io.h>.

    struct  bpp_pins {
       uchar_t  output_reg_pins;  /* pins in P_OR register */
       uchar_t  input_reg_pins;   /* pins in P_IR register */
    };
    
    /* Values for output_reg_pins field */
    #define BPP_SLCTIN_PIN  0x01  /* Select in pin */
    #define BPP_AFX_PIN     0x02  /* Auto feed pin */
    #define BPP_INIT_PIN    0x04  /* Initialize pin */
    #define BPP_V1_PIN      0x08  /* reserved pin 1 */
    #define BPP_V2_PI       0x10  /* reserved pin 2 */
    #define BPP_V3_PIN      0x20  /* reserved pin 3 */
    #define BPP_ERR_PIN     0x01  /* Error pin */
    #define BPP_SLCT_PIN    0x02  /* Select pin */
    #define BPP_PE_PIN      0x04  /* Paper empty pin */
    

     

    Error Pins Structure

    This structure is defined in the include file <sys/bpp_io.h>.

    struct bpp_error_status {
            char    timeout_occurred;       /* 1 if a timeout occurred */
            char    bus_error;      /* 1 if an SBus bus error */
            uchar_t pin_status;     /*
                             * status of pins which could
                             * cause an error
                             */
    };
    /* Values for pin_status field */
    #define BPP_ERR_ERR    0x01     /* Error pin active */
    #define BPP_SLCT_ERR   0x02     /* Select pin active */
    #define BPP_PE_ERR     0x04     /* Paper empty pin active */
    #define BPP_SLCTIN_ERR 0x10     /* Select in pin active */
    #define BPP_BUSY_ERR   0x40     /* Busy pin active */
    

     

    ERRORS

    EBADF

    The device is opened for write-only access and a read is attempted, or the device is opened for read-only access and a write is attempted.

    EBUSY

    The device has been opened and another open is attempted. An attempt has been made to unload the driver while one of the units is open.

    EINVAL

    A BPPIOC_SETPARMS ioctl is attempted with an out of range value in the bpp_transfer_parms structure. A BPPIOC_SETOUTPINS ioctl is attempted with an invalid value in the pins structure. An ioctl is attempted with an invalid value in the command argument. An invalid command argument is received during modload(1M) or modunload(1M).

    EIO

    The driver encountered an SBus bus error when attempting an access.

    A read or write does not complete properly, due to a peripheral error or a transfer timeout.

    A BPPIOC_TESTIO ioctl call is attempted while a condition exists which would prevent a transfer (such as a peripheral error).

    ENXIO

    The driver has received an open request for a unit for which the attach failed. The driver has received a read or write request for a unit number greater than the number of units available. The driver has received a write request for a unit which has an active peripheral error.

     

    FILES

    /dev/bppn

    bi-directional parallel port devices

     

    SEE ALSO

    ioctl(2), read(2), write(2), sbus(4)


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    APPLICATION PROGRAMMING INTERFACE
    Default Operation
    Write Operation
    Read Operations
    Read/Write Operation
    IOCTLS
    Transfer Parameters Structure
    Transfer Pins Structure
    Error Pins Structure
    ERRORS
    FILES
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру