The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

cdio (7)
  • >> cdio (7) ( Solaris man: Макропакеты и соглашения )
  •  

    NAME

    cdio - CD-ROM control operations
     
    

    SYNOPSIS

    #include <sys/cdio.h>
    

     

    DESCRIPTION

    The set of ioctl(2) commands described below are used to perform audio and CD-ROM specific operations. Basic to these cdio ioctl requests are the definitions in <sys/cdio.h>.

    Several CD-ROM specific commands can report addresses either in LBA (Logical Block Address) format or in MSF (Minute, Second, Frame) format. The READ HEADER, READ SUBCHANNEL, and READ TABLE OF CONTENTS commands have this feature.

    LBA format represents the logical block address for the CD-ROM absolute address field or for the offset from the beginning of the current track expressed as a number of logical blocks in a CD-ROM track relative address field. MSF format represents the physical address written on CD-ROM discs, expressed as a sector count relative to either the beginning of the medium or the beginning of the current track.  

    IOCTLS

    The following I/O controls do not have any additional data passed into or received from them.

    CDROMSTART

    This ioctl() spins up the disc and seeks to the last address requested.

    CDROMSTOP

    This ioctl() spins down the disc.

    CDROMPAUSE

    This ioctl() pauses the current audio play operation.

    CDROMRESUME

    This ioctl() resumes the paused audio play operation.

    CDROMEJECT

    This ioctl() ejects the caddy with the disc.

    CDROMCLOSETRAY

    This ioctl() closes the caddy with the disc.

    The following I/O controls require a pointer to the structure for that ioctl(), with data being passed into the ioctl().

    CDROMPLAYMSF

    This ioctl() command requests the drive to output the audio signals at the specified starting address and continue the audio play until the specified ending address is detected. The address is in MSF format. The third argument of this ioctl() call is a pointer to the type struct cdrom_msf.

    /*
    * definition of play audio msf structure
    */
    struct cdrom_msf {
            unsigned char   cdmsf_min0;     /* starting minute*/
            unsigned char   cdmsf_sec0;     /* starting second*/
            unsigned char   cdmsf_frame0;   /*starting frame*/
            unsigned char   cdmsf_min1;     /* ending minute */
            unsigned char   cdmsf_sec1;     /* ending second */
            unsigned char   cdmsf_frame1;   /* ending frame */
    };
    

    The CDROMREADTOCENTRY ioctl request may be used to obtain the start time for a track. An approximation of the finish time can be obtained by using the CDROMREADTOCENTRY ioctl request to retrieve the start time of the track following the current track.

    The leadout track is the next consecutive track after the last audio track. Hence, the start time of the leadout track may be used as the effective finish time of the last audio track.

    CDROMPLAYTRKIND

    This ioctl() command is similar to CDROMPLAYMSF. The starting and ending address is in track/index format. The third argument of the ioctl() call is a pointer to the type struct cdrom_ti.

    /*
    * definition of play audio track/index structure
    */
    struct cdrom_ti {
            unsigned char   cdti_trk0;      /* starting track*/
            unsigned char   cdti_ind0;      /* starting index*/
            unsigned char   cdti_trk1;      /* ending track */
            unsigned char   cdti_ind1;      /* ending index */
    };
    

    CDROMVOLCTRL

    This ioctl() command controls the audio output level. The SCSI command allows the control of up to four channels. The current implementation of the supported CD-ROM drive only uses channel 0 and channel 1. The valid values of volume control are between 0x00 and 0xFF, with a value of 0xFF indicating maximum volume. The third argument of the ioctl() call is a pointer to struct cdrom_volctrl which contains the output volume values.

    /*
    * definition of audio volume control structure
    */
    struct cdrom_volctrl {
            unsigned char   channel0;
            unsigned char   channel1;
            unsigned char   channel2;
            unsigned char   channel3;
    };
    

    The following I/O controls take a pointer that will have data returned to the user program from the CD-ROM driver.

    CDROMREADTOCHDR

    This ioctl() command returns the header of the table of contents (TOC). The header consists of the starting tracking number and the ending track number of the disc. These two numbers are returned through a pointer of struct cdrom_tochdr. While the disc can start at any number, all tracks between the first and last tracks are in contiguous ascending order.

    /*
    * definition of read toc header structure
    */
    struct cdrom_tochdr {
            unsigned char   cdth_trk0;      /* starting track*/
            unsigned char   cdth_trk1;      /* ending track*/
    };
    

    CDROMREADTOCENTRY

    This ioctl() command returns the information of a specified track. The third argument of the function call is a pointer to the type struct cdrom_tocentry. The caller needs to supply the track number and the address format. This command will return a 4-bit adr field, a 4-bit ctrl field, the starting address in MSF format or LBA format, and the data mode if the track is a data track. The ctrl field specifies whether the track is data or audio.

    /*
    * definition of read toc entry structure
    */
    struct cdrom_tocentry {
            unsigned char  cdte_track;
            unsigned char  cdte_adr   :4;
            unsigned char  cdte_ctrl   :4;
            unsigned char  cdte_format;
            union {
                    struct {
                            unsigned char  minute;
                            unsigned char  second;
                            unsigned char  frame;
                    } msf;
                    int     lba;
            } cdte_addr;
            unsigned char  cdte_datamode;
    };
    

    To get the information from the leadout track, the following value is appropriate for the cdte_track field:

    CDROM_LEADOUT

    Leadout track

    To get the information from the data track, the following value is appropriate for the cdte_ctrl field:

    CDROM_DATA_TRACK

    Data track

    The following values are appropriate for the cdte_format field:

    CDROM_LBA

    LBA format

    CDROM_MSF

    MSF format

    CDROMSUBCHNL

    This ioctl() command reads the Q sub-channel data of the current block. The subchannel data includes track number, index number, absolute CD-ROM address, track relative CD-ROM address, control data and audio status. All information is returned through a pointer to struct cdrom_subchnl. The caller needs to supply the address format for the returned address.

    struct cdrom_subchnl {
            unsigned char   cdsc_format;
            unsigned char   cdsc_audiostatus;
            unsigned char   cdsc_adr:       4;
            unsigned char   cdsc_ctrl:      4;
            unsigned char   cdsc_trk;
            unsigned char   cdsc_ind;
            union {
                    struct {
                            unsigned char   minute;
                            unsigned char   second;
                            unsigned char   frame;
                    } msf;
                    int     lba;
            } cdsc_absaddr;
            union {
                    struct {
                            unsigned char   minute;
                            unsigned char   second;
                            unsigned char   frame;
                    } msf;
                    int     lba;
            } cdsc_reladdr;
    };
    

    The following values are valid for the audio status field returned from READ SUBCHANNEL command:

    CDROM_AUDIO_INVALID

    Audio status not supported.

    CDROM_AUDIO_PLAY

    Audio play operation in progress.

    CDROM_AUDIO_PAUSED

    Audio play operation paused.

    CDROM_AUDIO_COMPLETED

    Audio play successfully completed.

    CDROM_AUDIO_ERROR

    Audio play stopped due to error.

    CDROM_AUDIO_NO_STATUS

    No current audio status to return.

    CDROMREADOFFSET

    This ioctl() command returns the absolute CD-ROM address of the first track in the last session of a Multi-Session CD-ROM. The third argument of the ioctl() call is a pointer to an int.

    CDROMCDDA

    This ioctl() command returns the CD-DA data or the subcode data. The third argument of the ioctl() call is a pointer to the type struct cdrom_cdda. In addition to allocating memory and supplying its address, the caller needs to supply the starting address of the data, the transfer length in terms of the number of blocks to be transferred, and the subcode options. The caller also needs to issue the CDROMREADTOCENTRY ioctl() to find out which tracks contain CD-DA data before issuing this ioctl().

    /*
    * Definition of CD-DA structure
    */
    struct cdrom_cdda {
            unsigned int    cdda_addr;
            unsigned int    cdda_length;
            caddr_t         cdda_data;
            unsigned char   cdda_subcode;
    };
    

    cdda_addr signifies the starting logical block address.

    cdda_length signifies the transfer length in blocks. The length of the block depends on the cdda_subcode selection, which is explained below.

    To get the subcode information related to CD-DA data, the following values are appropriate for the cdda_subcode field:

    CDROM_DA_NO_SUBCODE

    CD-DA data with no subcode.

    CDROM_DA_SUBQ

    CD-DA data with sub Q code.

    CDROM_DA_ALL_SUBCODE

    CD-DA data with all subcode.

    CDROM_DA_SUBCODE_ONLY

    All subcode only.

    To allocate the memory related to CD-DA and/or subcode data, the following values are appropriate for each data block transferred:

    CD-DA data with no subcode

    2352 bytes

    CD-DA data with sub Q code

    2368 bytes

    CD-DA data with all subcode

    2448 bytes

    All subcode only

    96 bytes

    CDROMCDXA

    This ioctl() command returns the CD-ROM XA (CD-ROM Extended Architecture) data according to CD-ROM XA format. The third argument of the ioctl() call is a pointer to the type struct cdrom_cdxa. In addition to allocating memory and supplying its address, the caller needs to supply the starting address of the data, the transfer length in terms of number of blocks, and the format. The caller also needs to issue the CDROMREADTOCENTRY ioctl() to find out which tracks contain CD-ROM XA data before issuing this ioctl().

    /*
    * Definition of CD-ROM XA structure
    */
    struct cdrom_cdxa {
            unsigned int    cdxa_addr;
            unsigned int    cdxa_length;
            caddr_t         cdxa_data;
            unsigned char   cdxa_format;
    };
    

    To get the proper CD-ROM XA data, the following values are appropriate for the cdxa_format field:

    CDROM_XA_DATA

    CD-ROM XA data only

    CDROM_XA_SECTOR_DATA

    CD-ROM XA all sector data

    CDROM_XA_DATA_W_ERROR

    CD-ROM XA data with error flags data

    To allocate the memory related to CD-ROM XA format, the following values are appropriate for each data block transferred:

    CD-ROM XA data only

    2048 bytes

    CD-ROM XA all sector data

    2352 bytes

    CD-ROM XA data with error flags data

    2646 bytes

    CDROMSUBCODE

    This ioctl() command returns raw subcode data (subcodes P ~ W are described in the "Red Book," see SEE ALSO) to the initiator while the target is playing audio. The third argument of the ioctl() call is a pointer to the type struct cdrom_subcode. The caller needs to supply the transfer length in terms of number of blocks and allocate memory for subcode data. The memory allocated should be a multiple of 96 bytes depending on the transfer length.

    /*
    * Definition of subcode structure
    */
    struct cdrom_subcode {
            unsigned int    cdsc_length;
            caddr_t         cdsc_addr;
    };
    

    The next group of I/O controls get and set various CD-ROM drive parameters.

    CDROMGBLKMODE

    This ioctl() command returns the current block size used by the CD-ROM drive. The third argument of the ioctl() call is a pointer to an integer.

    CDROMSBLKMODE

    This ioctl() command requests the CD-ROM drive to change from the current block size to the requested block size. The third argument of the ioctl() call is an integer which contains the requested block size.

    This ioctl() command operates in exclusive-use mode only. The caller must ensure that no other processes can operate on the same CD-ROM device before issuing this ioctl(). read(2) behavior subsequent to this ioctl() remains the same: the caller is still constrained to read the raw device on block boundaries and in block multiples.

    To set the proper block size, the following values are appropriate:

    CDROM_BLK_512

    512 bytes

    CDROM_BLK_1024

    1024 bytes

    CDROM_BLK_2048

    2048 bytes

    CDROM_BLK_2056

    2056 bytes

    CDROM_BLK_2336

    2336 bytes

    CDROM_BLK_2340

    2340 bytes

    CDROM_BLK_2352

    2352 bytes

    CDROM_BLK_2368

    2368 bytes

    CDROM_BLK_2448

    2448 bytes

    CDROM_BLK_2646

    2646 bytes

    CDROM_BLK_2647

    2647 bytes

    CDROMGDRVSPEED

    This ioctl() command returns the current CD-ROM drive speed. The third argument of the ioctl() call is a pointer to an integer.

    CDROMSDRVSPEED

    This ioctl() command requests the CD-ROM drive to change the current drive speed to the requested drive speed. This speed setting is only applicable when reading data areas. The third argument of the ioctl() is an integer which contains the requested drive speed.

    To set the CD-ROM drive to the proper speed, the following values are appropriate:

    CDROM_NORMAL_SPEED

    150k/second

    CDROM_DOUBLE_SPEED

    300k/second

    CDROM_QUAD_SPEED

    600k/second

    CDROM_MAXIMUM_SPEED

    300k/second (2x drive) 600k/second (4x drive)

    Note that these numbers are only accurate when reading 2048 byte blocks. The CD-ROM drive will automatically switch to normal speed when playing audio tracks and will switch back to the speed setting when accessing data.

     

    SEE ALSO

    ioctl(2), read(2)

    N. V. Phillips and Sony Corporation, System Description Compact Disc Digital Audio, ("Red Book").

    N. V. Phillips and Sony Corporation, System Description of Compact Disc Read Only Memory, ("Yellow Book").

    N. V. Phillips, Microsoft, and Sony Corporation, System Description CD-ROM XA, 1991.

    Volume and File Structure of CD-ROM for Information Interchange, ISO 9660:1988(E).

    SCSI-2 Standard, document X3T9.2/86-109

    SCSI Multimedia Commands, Version 2 (MMC-2)  

    NOTES

    The CDROMCDDA, CDROMCDXA, CDROMSUBCODE, CDROMGDRVSPEED, CDROMSDRVSPEED, and some of the block sizes in CDROMSBLKMODE are designed for new Sun-supported CD-ROM drives and might not work on some of the older CD-ROM drives.

    CDROMCDDA, CDROMCDXA and CDROMSUBCODE will return error if the transfer length exceeds valid limits as determined appropriate. Example: for MMC-2 drives, length can not exceed 3 bytes (i.e. 0xffffff). The same restriction is enforced for older, pre-MMC-2 drives, as no limit was published for these older drives (and 3 bytes is reasonable for all media). Note that enforcing this limit does not imply that values passed in below this limit will actually be applicable for each and every piece of media.

    The interface to this device is preliminary and subject to change in future releases. Programs should be written in a modular fashion so that future changes can be easily incorporated.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    IOCTLS
    SEE ALSO
    NOTES


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру