The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

gstripe (8)
  • >> gstripe (8) ( FreeBSD man: Команды системного администрирования )

  • BSD mandoc
     

    NAME

    
    
    gstripe
    
     - control utility for striped devices
    
     
    

    SYNOPSIS

    create [-v ] [-s stripesize ] name prov prov ...
    destroy [-fv ] name ...
    label [-hv ] [-s stripesize ] name prov prov ...
    stop [-fv ] name ...
    clear [-v ] prov ...
    dump prov ...
    list
    status
    load
    unload  

    DESCRIPTION

    The utility is used for setting up a stripe on two or more disks. The striped device can be configured using two different methods: ``manual'' or ``automatic'' When using the ``manual'' method, no metadata are stored on the devices, so the striped device has to be configured by hand every time it is needed. The ``automatic'' method uses on-disk metadata to detect devices. Once devices are labeled, they will be automatically detected and configured.

    The first argument to indicates an action to be performed:

    create
    Set up a striped device from the given devices with specified name This is the ``manual'' method and the stripe will not exist after a reboot (see Sx DESCRIPTION above). The kernel module geom_stripe.ko will be loaded if it is not loaded already.
    label
    Set up a striped device from the given devices with the specified name This is the ``automatic'' method, where metadata are stored in every device's last sector. The kernel module geom_stripe.ko will be loaded if it is not loaded already.
    stop
    Turn off an existing striped device by its name This command does not touch on-disk metadata!
    destroy
    Same as stop
    clear
    Clear metadata on the given devices.
    dump
    Dump metadata stored on the given devices.
    list
    See geom(8).
    status
    See geom(8).
    load
    See geom(8).
    unload
    See geom(8).

    Additional options:

    -f
    Force the removal of the specified striped device.
    -h
    Hardcode providers' names in metadata.
    -s stripesize
    Specifies size of stripe block in bytes. The stripesize must be a multiple of the largest sector size of all the providers.
    -v
    Be more verbose.

     

    SYSCTL VARIABLES

    The following sysctl(8) variables can be used to control the behavior of the STRIPE GEOM class. The default value is shown next to each variable.

    kern.geom.stripe.debug : 0
    Debug level of the STRIPE GEOM class. This can be set to a number between 0 and 3 inclusive. If set to 0 minimal debug information is printed, and if set to 3 the maximum amount of debug information is printed.
    kern.geom.stripe.fast : 0
    If set to a non-zero value enable ``fast mode'' instead of the normal ``economic mode'' Compared to ``economic mode'' ``fast mode'' uses more memory, but it is much faster for smaller stripe sizes. If enough memory cannot be allocated, STRIPE will fall back to ``economic mode''
    kern.geom.stripe.maxmem : 13107200
    Maximum amount of memory that can be consumed by ``fast mode'' (in bytes). This sysctl(8) variable is read-only and can only be set as a tunable in loader.conf5.
    kern.geom.stripe.fast_failed
    A count of how many times ``fast mode'' has failed due to an insufficient amount of memory. If this value is large, you should consider increasing the kern.geom.stripe.maxmem value.

     

    EXIT STATUS

    Exit status is 0 on success, and 1 if the command fails.  

    EXAMPLES

    The following example shows how to set up a striped device from four disks with a 128KB stripe size for automatic configuration, create a file system on it, and mount it:
    gstripe label -v -s 131072 data /dev/da0 /dev/da1 /dev/da2 /dev/da3
    newfs /dev/stripe/data
    mount /dev/stripe/data /mnt
    [...]
    umount /mnt
    gstripe stop data
    gstripe unload
    
     

    COMPATIBILITY

    The interleave is in number of bytes, unlike ccdconfig(8) and atacontrol(8) which use the number of sectors. A ccdconfig(8) ileave of `128' is 64 KB (128 512B sectors). The same stripe interleave would be specified as `65536' for .  

    SEE ALSO

    geom(4), loader.conf5, atacontrol(8), ccdconfig(8), geom(8), mount(8), newfs(8), sysctl(8), umount(8), vinum(8)  

    HISTORY

    The utility appeared in Fx 5.3 .  

    AUTHORS

    An Pawel Jakub Dawidek Aq pjd@FreeBSD.org


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    SYSCTL VARIABLES
    EXIT STATUS
    EXAMPLES
    COMPATIBILITY
    SEE ALSO
    HISTORY
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру