The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

ng_nat (4)
  • >> ng_nat (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    ng_nat
    
     - NAT netgraph node type
    
     
    

    SYNOPSIS

       #include <netgraph/ng_nat.h>
     

    DESCRIPTION

    An node performs network address translation (NAT) of packets passing through it. A nat node uses libalias(3) engine for packet aliasing.  

    HOOKS

    This node type has two hooks:

    out
    Packets received on this hook are considered outgoing and will be masqueraded to a configured address.
    in
    Packets coming on this hook are considered incoming and will be dealiased.

     

    CONTROL MESSAGES

    This node type supports the generic control messages, plus the following:

    NGM_NAT_SET_IPADDR (setaliasaddr )
    Configure aliasing address for a node. After both hooks have been connected and aliasing address was configured, a node is ready for aliasing operation.
    NGM_NAT_SET_MODE (setmode )
    Set node's operation mode using supplied Vt struct ng_nat_mode.
    struct ng_nat_mode {
            uint32_t        flags;
            uint32_t        mask;
    };
    /* Supported flags: */
    #define NG_NAT_LOG                      0x01
    #define NG_NAT_DENY_INCOMING            0x02
    #define NG_NAT_SAME_PORTS               0x04
    #define NG_NAT_UNREGISTERED_ONLY        0x10
    #define NG_NAT_RESET_ON_ADDR_CHANGE     0x20
    #define NG_NAT_PROXY_ONLY               0x40
    #define NG_NAT_REVERSE                  0x80
    
    NGM_NAT_SET_TARGET (settarget )
    Configure target address for a node. When an incoming packet not associated with any pre-existing aliasing link arrives at the host machine, it will be sent to the specified address.
    NGM_NAT_REDIRECT_PORT (redirectport )
    Redirect incoming connections arriving to given port(s) to another host and port(s). The following Vt struct ng_nat_redirect_port must be supplied as argument.
    #define NG_NAT_DESC_LENGTH      64
    struct ng_nat_redirect_port {
            struct in_addr  local_addr;
            struct in_addr  alias_addr;
            struct in_addr  remote_addr;
            uint16_t        local_port;
            uint16_t        alias_port;
            uint16_t        remote_port;
            uint8_t         proto;
            char            description[NG_NAT_DESC_LENGTH];
    };
    

    Redirection is assigned an unique ID which is returned as response to this message, and information about redirection added to list of static redirects which later can be retrieved by NGM_NAT_LIST_REDIRECTS message.

    NGM_NAT_REDIRECT_ADDR (redirectaddr )
    Redirect traffic for public IP address to a machine on the local network. This function is known as static NAT The following Vt struct ng_nat_redirect_addr must be supplied as argument.
    struct ng_nat_redirect_addr {
            struct in_addr  local_addr;
            struct in_addr  alias_addr;
            char            description[NG_NAT_DESC_LENGTH];
    };
    

    Unique ID for this redirection is returned as response to this message.

    NGM_NAT_REDIRECT_PROTO (redirectproto )
    Redirect incoming IP packets of protocol proto (see protocols(5)) to a machine on the local network. The following Vt struct ng_nat_redirect_proto must be supplied as argument.
    struct ng_nat_redirect_proto {
            struct in_addr  local_addr;
            struct in_addr  alias_addr;
            struct in_addr  remote_addr;
            uint8_t         proto;
            char            description[NG_NAT_DESC_LENGTH];
    };
    

    Unique ID for this redirection is returned as response to this message.

    NGM_NAT_REDIRECT_DYNAMIC (redirectdynamic )
    Mark redirection with specified ID as dynamic, i.e., it will serve for exactly one next connection and then will be automatically deleted from internal links table. Only fully specified links can be made dynamic. The redirection with this ID is also immediately deleted from user-visible list of static redirects (available through NGM_NAT_LIST_REDIRECTS message).
    NGM_NAT_REDIRECT_DELETE (redirectdelete )
    Delete redirection with specified ID (currently active connections are not affected).
    NGM_NAT_ADD_SERVER (addserver )
    Add another server to a pool. This is used to transparently offload network load on a single server and distribute the load across a pool of servers, also known as LSNAT (RFC 2391). The following Vt struct ng_nat_add_server must be supplied as argument.
    struct ng_nat_add_server {
            uint32_t        id;
            struct in_addr  addr;
            uint16_t        port;
    };
    

    First, the redirection is set up by NGM_NAT_REDIRECT_PORT or NGM_NAT_REDIRECT_ADDR Then, ID of that redirection is used in multiple NGM_NAT_ADD_SERVER messages to add necessary number of servers. For redirections created by NGM_NAT_REDIRECT_ADDR the port is ignored and could have any value. Original redirection's parameters local_addr and local_port are also ignored after NGM_NAT_ADD_SERVER was used (they are effectively replaced by server pool).

    NGM_NAT_LIST_REDIRECTS (listredirects )
    Return list of configured static redirects as Vt struct ng_nat_list_redirects.
    struct ng_nat_listrdrs_entry {
            uint32_t        id;             /* Anything except zero */
            struct in_addr  local_addr;
            struct in_addr  alias_addr;
            struct in_addr  remote_addr;
            uint16_t        local_port;
            uint16_t        alias_port;
            uint16_t        remote_port;
            uint16_t        proto;          /* Valid proto or NG_NAT_REDIRPROTO_ADDR */
            uint16_t        lsnat;          /* LSNAT servers count */
            char            description[NG_NAT_DESC_LENGTH];
    };
    struct ng_nat_list_redirects {
            uint32_t                total_count;
            struct ng_nat_listrdrs_entry redirects[];
    };
    #define NG_NAT_REDIRPROTO_ADDR  (IPPROTO_MAX + 3)
    

    Entries of the redirects array returned in the unified format for all redirect types. Ports are meaningful only if protocol is either TCP or UDP and static NAT redirection (created by NGM_NAT_REDIRECT_ADDR is indicated by proto set to NG_NAT_REDIRPROTO_ADDR If lsnat servers counter is greater than zero, then local_addr and local_port are also meaningless.

    NGM_NAT_PROXY_RULE (proxyrule )
    Specify a transparent proxying rule (string must be supplied as argument). See libalias(3) for details.

    In all redirection messages local_addr and local_port mean address and port of target machine in the internal network, respectively. If alias_addr is zero, then default aliasing address (set by NGM_NAT_SET_IPADDR is used. Connections can also be restricted to be accepted only from specific external machines by using non-zero remote_addr and/or remote_port Each redirection assigned an ID which can be later used for redirection manipulation on individual basis (e.g., removal). This ID guaranteed to be unique until the node shuts down (it will not be reused after deletion), and is returned to user after making each new redirection or can be found in the stored list of all redirections. The description passed to and from node unchanged, together with ID providing a way for several entities to concurrently manipulate redirections in automated way.  

    SHUTDOWN

    This node shuts down upon receipt of a NGM_SHUTDOWN control message, or when both hooks are disconnected.  

    EXAMPLES

    In the following example, the packets are injected into a nat node using the ng_ipfw4 node.
    # Create NAT node
    ngctl mkpeer ipfw: nat 60 out
    ngctl name ipfw:60 nat
    ngctl connect ipfw: nat: 61 in
    ngctl msg nat: setaliasaddr x.y.35.8
    
    # Divert traffic into NAT node
    ipfw add 300 netgraph 61 all from any to any in via fxp0
    ipfw add 400 netgraph 60 all from any to any out via fxp0
    
    # Let packets continue with after being (de)aliased
    sysctl net.inet.ip.fw.one_pass=0
    

    The node can be inserted right after the ng_iface4 node in the graph. In the following example, we perform masquerading on a serial line with HDLC encapsulation.

    /usr/sbin/ngctl -f- <<-SEQ
            mkpeer cp0: cisco rawdata downstream
            name cp0:rawdata hdlc
            mkpeer hdlc: nat inet in
            name hdlc:inet nat
            mkpeer nat: iface out inet
            msg nat: setaliasaddr x.y.8.35
    SEQ
    ifconfig ng0 x.y.8.35 x.y.8.1
    
     

    SEE ALSO

    libalias(3), ng_ipfw4, natd(8), ngctl(8)  

    HISTORY

    The node type was implemented in Fx 6.0 .  

    AUTHORS

    An Gleb Smirnoff Aq glebius@FreeBSD.org


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HOOKS
    CONTROL MESSAGES
    SHUTDOWN
    EXAMPLES
    SEE ALSO
    HISTORY
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру