>FreeBSD 6.0.
>
>Пробовал установить VPN сервер:
>- radius
>- progresql
>- ppp (модифицированный)
>
>в ядре необходимо было выставить опцию "dummynet".
>выставлена, и ядро было перекомпилено.
>далее, после ребута, пинг на одном интерфейсе куда-либо пропал.
>погрешив на файрвол, выключил его в rc.conf, там же зарубил самбу и
>радиус.
>вовремя перезагрузки увидал, что есть жалобы на /dev/*
>сделал fsck, ушел в ребут.
>после этого машинка оттуда не пришла :)
>висит приглашение:
>
>FreeBSD/i386 boot
>Default: 0:ad(0,a)/boot/ed/kernel
-------------------------^^--------> это еще что за На...?>boot:
>
>ведь есть же старое ядро? можно ли загрузиться с него?
>
>ЗЫ прошу прощения за ламерские вопросы, но, ковер по мне плачет, не
>хочется очень :)
- power off
- загрузка в single-user mode
- cat /etc/fstab - смотреть на какие /dev делать fsck
# fsck -y /
# mount /
# fsck -y /usr
# mount /usr
и т д и тп
# man boot
...
The remainder of this subsection deals only with the boot blocks. The
loader(8) program is documented separately.
After the boot blocks have been loaded, you should see a prompt similar
to the following:
>> FreeBSD/i386 BOOT
Default: 0:ad(0,a)/boot/loader
boot:
The automatic boot will attempt to load /boot/loader from partition `a'
of either the floppy or the hard disk. This boot may be aborted by typ-
ing any character on the keyboard at the `boot:' prompt. At this time,
the following input will be accepted:
? Give a short listing of the files in the root directory of the
default boot device, as a hint about available boot files. (A ?
may also be specified as the last segment of a path, in which
case the listing will be of the relevant subdirectory.)
bios_drive:interface(unit,[slice,]part)filename [-aCcDdghmnPprsv]
[-Sspeed]
Specify boot file and flags.
bios_drive
The drive number as recognized by the BIOS. 0 for the
first drive, 1 for the second drive, etc.
interface
The type of controller to boot from. Note that the con-
troller is required to have BIOS support since the BIOS
services are used to load the boot file image.
The supported interfaces are:
ad ST506, IDE, ESDI, RLL disks on a WD100[2367] or
lookalike controller
fd 5 1/4" or 3 1/2" High density floppies
da SCSI disk on any supported SCSI controller
unit The unit number of the drive on the interface being used.
0 for the first drive, 1 for the second drive, etc.
[slice,]part
The partition letter inside the BSD portion of the disk.
See bsdlabel(8). By convention, only partition `a' con-
tains a bootable image. If sliced disks are used
(``fdisk partitions''), any slice (1 for the first slice,
2 for the second slice, etc.) can be booted from, with
the default (if not specified) being the active slice or,
otherwise, the first FreeBSD slice. If slice is speci-
fied as 0, the first FreeBSD slice (also known as
``compatibility'' slice) is booted from.
filename
The pathname of the file to boot (relative to the root
directory on the specified partition). Defaults to
/boot/kernel/kernel. Symbolic links are not supported
(hard links are).
[-aCcDdghmnPpqrsv] [-Sspeed]
Boot flags:
-a during kernel initialization, ask for the device to
mount as the root file system.
-C try to mount root file system from a CD-ROM.
-c this flag is currently a no-op.
-D boot with the dual console configuration. In the
single configuration, the console will be either
the internal display or the serial port, depending
on the state of the -h option below. In the dual
console configuration, both the internal display
and the serial port will become the console at the
same time, regardless of the state of the -h
option.
-d enter the DDB kernel debugger (see ddb(4)) as early
as possible in kernel initialization.
-g use the GDB remote debugging protocol.
-h force the serial console. For instance, if you
boot from the internal console, you can use the -h
option to force the kernel to use the serial port
as its console device. The serial port driver
sio(4) has a flag (0x20) to override this option.
If that flag is set, the serial port will always be
used as the console, regardless of the -h option
described here. See the man page for sio(4) for
more details.
-m mute the console to suppress all console input and
output during the boot.
-n ignore key press to interrupt boot before loader(8)
is invoked.
-P probe the keyboard. If no keyboard is found, the
-D and -h options are automatically set.
-p pause after each attached device during the device
probing phase.
-q be quiet, do not write anything to the console
unless automatic boot fails or is disabled. This
option only affects second-stage bootstrap, to pre-
vent next stages from writing to the console use in
combination with the -m option.
-r use the statically configured default for the
device containing the root file system (see
config(8)). Normally, the root file system is on
the device that the kernel was loaded from.
-s boot into single-user mode; if the console is
marked as ``insecure'' (see ttys(5)), the root
password must be entered.
-Sspeed
set the speed of the serial console to speed. The
default is 9600 unless it has been overridden by
setting BOOT_COMCONSOLE_SPEED in make.conf(5) and
recompiling and reinstalling the boot blocks.
-v be verbose during device probing (and later).
You may put a BIOS drive number, a controller type, a unit number, a par-
tition, a kernel file name, and any valid option in /boot.config to set
defaults. Enter them in one line just as you type at the `boot:' prompt.
FILES
/boot.config parameters for the boot blocks (optional)
/boot/boot1 first stage bootstrap file
/boot/boot2 second stage bootstrap file
/boot/loader third stage bootstrap
/boot/kernel/kernel
default kernel
/boot/kernel.old/kernel
typical non-default kernel (optional)
# man loader
Вариант для распечатки
OpenNET: Виртуальная конференция (Public)
on 10-Окт-06, 16:12 
