Поможите.
Соединил 2821 по Е1 с Меридианом.
Звонок с Меридиана на циску - все ок.
Обратно -ни в какую :(Вот лог.
*Jan 29 07:51:49.723: ISDN Se0/0/1:15 Q931: RX <- SETUP pd = 8 callref = 0x3700
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98388
Exclusive, Channel 8
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0980, '399'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '564'
Plan:Private, Type:Unknown
Sending Complete
*Jan 29 07:51:49.735: ISDN Se0/0/1:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xB700
Channel ID i = 0xA98388
Exclusive, Channel 8
*Jan 29 07:51:49.743: ISDN Se0/0/1:15 Q931: TX -> ALERTING pd = 8 callref = 0xB700
Progress Ind i = 0x8188 - In-band info or appropriate now available
*Jan 29 07:51:58.179: ISDN Se0/0/1:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x3700
Cause i = 0x8190 - Normal call clearing
*Jan 29 07:51:58.179: ISDN Se0/0/1:15 Q931: TX -> RELEASE pd = 8 callref = 0xB700
*Jan 29 07:51:58.251: ISDN Se0/0/1:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x3700
Router2821#csim start 399
csim: called number = 399, loop count = 1 ping count = 0
csim err:csim_do_test invalid major major(16) minor(0)
csim: loop = 1, failed = 0
csim: call attempted = 1, setup failed = 0, tone failed = 0
Router2821#
*Jan 29 07:52:55.979: ISDN Se0/0/1:15 Q931: Applying typeplan for sw-type 0x12 is 0x4 0x1, Called num 399
*Jan 29 07:52:55.979: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8 callref = 0x00BB
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Called Party Number i = 0xC1, '399'
Plan:ISDN, Type:Subscriber(local)
*Jan 29 07:52:55.979: ISDN Se0/0/1:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x00BB
Cause i = 0x82AF - Resource unavailable, unspecified
*Jan 29 07:52:56.059: ISDN Se0/0/1:15 Q931: RX <- RELEASE pd = 8 callref = 0x80BB
*Jan 29 07:52:56.063: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x00BB
Router2821#
Router2821#sh voice dsp
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
----------------------------FLEX VOICE CARD 0 ------------------------------
*DSP VOICE CHANNELS*
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ======== ======= ===== ======= === == ========= == ==== ============
*DSP SIGNALING CHANNELS*
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ======== ======= ===== ======= === == ========= == ==== ============
C5510 001 01 {flex} 7.4.3 alloc idle 0 0 0/1/0 02 0 0/0
C5510 001 02 {flex} 7.4.3 alloc idle 0 0 0/1/1 02 0 0/0
C5510 001 03 {flex} 7.4.3 alloc idle 0 0 0/2/0 02 0 2/0
C5510 001 04 {flex} 7.4.3 alloc idle 0 0 0/2/1 02 0 14/0
------------------------END OF FLEX VOICE CARD 0 ----------------------------
Выдержки из конфига:
controller E1 0/0/1
framing NO-CRC4
pri-group timeslots 1-8,16
description to_CS1000_PRI
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
voice-port 0/0/1:15
cptone RU
voice-port 0/2/1
dial-peer voice 1 pots
destination-pattern 3..
incoming called-number .T
direct-inward-dial
port 0/0/1:15
forward-digits all
!
dial-peer voice 2 pots
destination-pattern 564
port 0/2/1
Вариант для распечатки
Маршрутизаторы CISCO и др. оборудование. (Сопряжение с АТС)
(ok) on 29-Янв-10, 10:39 
