mknod /dev/ircomm0 c 161 0 mknod /dev/ircomm1 c 161 1 mknod /dev/irlpt0 c 161 16 mknod /dev/irlpt1 c 161 17 mknod /dev/irnet c 10 187 chmod 666 /dev/ir*
First you should put your IrDA devices in range. Though it might be possible that the Linux/IrDA service detects every new device automagically I only have good experience with the devices in range during the configuration process.
Keep your infrared devices together in a range below one meter and an angle of 30 degree. There has to be a direct line of sight between them. If this is not possible, you may use a mirror (an unused M$ CD should work quite good).
Add the following lines to your /etc/conf.modules file:
# IrDA over a normal serial port, or a serial port compatible IrDA port (SIR) alias tty-ldisc-11 irtty # IrCOMM (for printing, PPP, Minicom etc) alias char-major-161 ircomm-tty # if you want IrCOMM support # IRLAN # But currently the IrLAN protocol is no longer maintained # by the Linux/IrDA core team. alias irlan0 irlan # To be able to attach some serial dongles # These values are hard-coded in irattach (not instance order) alias irda-dongle-0 tekram # Tekram IrMate IR-210B alias irda-dongle-1 esi # ESI JetEye alias irda-dongle-2 actisys # Actisys IR-220L alias irda-dongle-3 actisys # Actisys IR-220L+ alias irda-dongle-4 girbil # Greenwich GIrBIL alias irda-dongle-5 litelink # Parallax LiteLink/ESI JetEye alias irda-dongle-6 airport # Adaptec Airport 1000 and 2000 alias irda-dongle-7 old_belkin # Belkin (old) SmartBeam dongle alias irda-dongle-8 ep7211_ir # Cirrus Logic EP7211 Processor (ARM) alias irda-dongle-9 mcp2120 # MCP2120 (Microchip) based alias irda-dongle-10 act200l # ACTiSYS Ir-200L alias irda-dongle-11 ma600 # Mobile Action ma600 # To use the FIR driver. This applies only to the specific device!!! #options nsc-ircc dongle_id=0x09 # NSC driver on a IBM Thinkpad laptop #options nsc-ircc dongle_id=0x08 # HP Omnibook 6000 #alias irda0 nsc-ircc # options smc-ircc ircc_irq= ircc_dma= # alias irda0 smc-ircc # options toshoboe max_baud= # alias irda0 toshoboe # options w83977af_ir io= io2= irq= qos_mtt_bits= # alias irda0 w83977af_ir # IrNET module... alias char-major-10-187 irnet # Official allocation of IrNET
Note: With Debian GNU/Linux however you shouldn't edit /etc/modules.conf directly, instead place the lines inside /etc/modutils/irda and run update-modules afterwards.
Make sure your infrared port is enabled in the BIOS and check what interrupt and port address it uses. With some laptops it seems necessary to have Microsoft-Windows installed to be able to set BIOS parameters.
I have got reports, that connected to a docking station the infrared port was disabled on some laptops.
Please decide first whether you want to set up Irda either in SIR or in FIR mode. It is recommended to start with SIR.
Choose the ttySx according to your SIR port. Hint: dmesg | grep tty (for details see the chapter Starting the IrDA Stack below).
To get the SIR "serial" device have a look into the BIOS. Then run dmesg | grep tty to get a survey of tty devices supported by your machine. Now try to choose the one, which is probably the IrDA device.
If you don't succeed with SIR (which seems a rare case) you may try FIR. First look up the BIOS. To avoid some conflicts with serial devices you should do setserial /dev/ttySx uart none. Note: never use setserial /dev/ttySx uart none, when setting up IrDA in SIR mode.
From Florian Lohoff You should also set "port 0x0 irq 0" otherwise you will see interesting effects if there is suddenly a different S1 e.g. by inserting a modem PCMCIA card. The serial driver will then touch the OLD ports without having acquired those which will cause the irda stuff to die/hang. This is a bug i havent been able to find in the serial driver but it definitly exists (Put a printk into the serial_out serial_in stuff).
Is some cases IRQ conflicts may occur, especially conflicts with sound, PCMCIA or the hotplug system have been reported. Check cat /proc/interrupts to get some information about IRQ usage on your machine.
Most important, you must sync your disks!!! Maybe you have to reboot your machine. Have you read the disclaimer?
There are three sorts of low level drivers: SIR, FIR and dongle for machines without an in-built InfraRed port. To start with Linux/IrDA I recommend to use the SIR method.
Load the modules modprobe irda irtty. irattach /dev/ttyS1 -s to attach the IrDA device to the IrDA services. Check lsmod and dmesg.
irdadump should show all available IrDA devices in range now. Hint: If you are connecting different Linux boxes, you may use hostname YOUR_HOSTNAME to set a unique hostname for each computer.
On the "server" side do pppd /dev/ircomm0 LOCAL_IP:REMOTE_IP On the "client" side do pppd /dev/ircomm0 .
You may now test the connection with ping. And use all sorts of networking connections (ssh, NFS, ...) now.
Закладки на сайте
Проследить за страницей
Created 1996-2023 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру