The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

CPU_SOEKRIS (4)
  • >> CPU_SOEKRIS (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    CPU_ELAN
    
     - AMD Elan 520 CPU support
    
     
    

    SYNOPSIS

    options CPU_ELAN options CPU_ELAN_PPS options CPU_ELAN_XTAL

    machdep.elan_gpio_config
    machdep.elan_freq

    options CPU_SOEKRIS  

    DESCRIPTION

    The options CPU_ELAN enables support for the AMD Elan 520 CPU.

    A device /dev/elan-mmcr exports the MMCR register bank to userland using mmap(2).

    The i8254 timer will be adjusted to the slightly unorthodox frequency 1189161 Hz (32768 * 45 * 25 / 31) employed by the Elan.

    A timecounter named ``ELAN '' is implemented using the general purpose timer 2, but it will not be usable unless HZ is configured at 150 or higher. This timecounter is much better than the ``i8254 '' timecounter and should be used at all times.

    The machdep.elan_gpio_config sysctl(8) variable enables configuration of the GPIO pins of the CPU. The string must be exactly 32 characters long. A `-' means the GPIO is unavailable. A `l' (lower-case ell) configures a led(4) device (active low). A `L' configures a led(4) device (active high). A `.' means no configuration for this GPIO. These led(4) devices will be named /dev/led/gpio%d For meaning of `P' , `e' and `E' , see under options CPU_ELAN_PPS

    The options CPU_ELAN_XTAL and the machdep.elan_freq sysctl(8) variable can be used to set the CPU clock crystal frequency in Hz. The default is 33333333 Hz.

    The options CPU_ELAN_PPS enables precision timestamping using the RFC2783 PPS-API via the /dev/elan-mmcr device. The resolution will be approximately 125 nsec and the precision ± 125 nsec. (For 125 nsec read ``4 / CPU clock crystal frequency .''

    The input signal must be connected to the TMR1IN pin and a GPIO pin. The GPIO pin must be configured with a `P' in machdep.elan_gpio_config

    In addition, one GPIO pin can be configured with either `e' (active low) or `E' (active high) to become a ``echo'' output of the input signal. Please notice that this signal is not suitable for calibration.

    If the options CPU_SOEKRIS is given, the support will additionally be tailored to the Soekris Engineering 45xx series of embedded computers. The ``error'' led will be configured (as /dev/led/error and the GPIO pins which are not available will be disabled.  

    SEE ALSO

    led(4), sysctl(8)  

    HISTORY

    The code first appeared in Fx 4.7 .  

    AUTHORS

    An Poul-Henning Kamp Aq phk@FreeBSD.org


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    SEE ALSO
    HISTORY
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру