yuvkineco reverts to original non-interlaced frames,
from NTSC video which was film sourced and 2-3 pulled down.
Input fps code must be 4(29.97fps), output fps code can be selected
from 1(23.97fps) to 4(29.97fps). If 2, 3 or 4 selected, duplicated
frames remain but their are also reverted to non-interlaced.
If input was non-interlaced, only do remove duplicated frames.
Interlaced frame detection may fail in conditions like:
Pull down cycle changed (video editing).
Low quality pull down.
Motionless scene.
If -CPATH was specified, yuvkineco outputs 2-3 pull down
cycle list to the file. You can edit this file by hand and feed it
to yuvkineco with -O or -N option to correct mistake
of 1st yuvkineco.
Try -C and see cycle list.
EXAMPLE #1: for 24p movie / automatically
lav2yuv 60i.eli | \
yuvkineco -F 1 | yuv2lav -f a -I 0 -o 24p.avi EXAMPLE #2: for 30p/24p mix / automatically
lav2yuv 60i.eli | \
yuvkineco -F 4 | yuv2lav -f a -I 0 -o 30p.avi EXAMPLE #3: for 24p movie / check and repair
lav2yuv 60i.eli | \
yuvkineco -F 1 -C 60i.23c | \
yuv2lav -f a -I 1 -o take1.avi
glav -F +n take1.avi # check and edit 60i.23c
lav2yuv take1.avi | \
yuvkineco -F 1 -N 60i.23c | \
yuv2lav -f a -I 0 -o take2.avi EXAMPLE #4: for 24p movie / check and retry
lav2yuv 60i.eli | \
yuvkineco -F 1 -C 60i.23c | \
yuv2lav -f a -I 0 -o take1.avi
glav -F +n take1.avi # check and edit 60i.23c
lav2yuv 60i.eli | \
yuvkineco -F 1 -O 60i.23c | \
yuv2lav -f a -I 0 -o take2.avi
OPTIONS
yuvkineco accepts the following options:
-F FPSCODE
Set output fps code (default: same as input).
-C PATH
Specify 2-3 pull down cycle list file name to write.
-O PATH
Specify cycle list name to read with old yuv stream to retry.
-N PATH
Specify cycle list name to read with new yuv stream to repair.
-S MIN
Use yuvycsnoise(1) as preprocessor and specify minimum threshold.
-n LEVEL
Specify noise level of input (default: 10).
This affects both pulldown cycle detection and deinterlacing.
-c THRESHOLD
Specify threshold to decide pictures in 2 frames are same (default: 4).
yuvkineco compares several frames,
searches pair of frame they contain same pictures,
to decide which frame should be dropped.
If THRESHOLD is 0,
pair which has smallest difference will be selected.
If 16, selected from pairs those have differences smaller than average.
-i PERMIL
yuvkineco deinterlaces each frame after 2-3 pulldown reverting
process, specify how much pixels deinterlaced to decide to use
or not use deinterlacing result (default: 10).
If PERMIL is 10 and 1% or more of pixels deinterlaced,
deinterlacing result will be used.
If 0, always deinterlacing result will be used.
If 1000, deinterlacing result will not be used,
but deinterlacing process will run on all of frames.
To disable deinterlacing process, specify negative value.
-u
Set interlace information in header of output to unknown
(default: non-interlaced).
AUTHOR
yuvkineco was written by Kawamata/Hitoshi.
If you have questions, remarks, problems or you just want to contact
the developers, the main mailing list for the MJPEG-tools is:
mjpeg-users@lists.sourceforge.net
